Field checklist for ABB KA1-8029 1SFA616920R8029
Start the ABB KA1-8029 1SFA616920R8029 enquiry with a precise equipment identity and a defined plant function. The verified values below establish a technical baseline; they do not replace checking the delivered unit.
Verified parameters and fit limits
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | KA1-8029 1SFA616920R8029 |
| Product family | KA1 |
| Component role | 30 mm black pilot-device mounting adaptor |
| Type | KA1-8029 |
| ABB order code | 1SFA616920R8029 |
| Part | Black plastic adaptor |
| Mounting | 30 mm pilot-device application |
| Compatible devices | Check pushbutton, selector, pilot light or buzzer fit |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
Before signing off KA1-8029 1SFA616920R8029, check the current ABB documentation and the actual nameplate. Family-level information must not be used as a guaranteed option for every configuration.
What changes at installation?
Installing KA1-8029 1SFA616920R8029 may affect adjacent wiring, panel access and auxiliary accessories. Check clearance and isolate the correct energy sources under the site's permit system.
Before disturbing KA1-8029 1SFA616920R8029, save photos, configuration, parameter values and an alarm baseline. Keep removed parts identifiable until acceptance is signed.
What problem does it solve?
ABB KA1-8029 1SFA616920R8029 is selected to adapt the selected operator to the panel opening. State the actual circuit, loop or motor tag and the operating problem before deciding on a replacement.
A request for KA1-8029 1SFA616920R8029 without site duty, installed revision or failure evidence can lead to a technically different part being offered.
Which interfaces must match?
For KA1-8029 1SFA616920R8029, confirm panel cutout, operator generation, fixing and legend clearance. Compare the original label, mounting, field terminals and power/control supplies with the ABB product reference.
Keep the KA1-8029 1SFA616920R8029 electrical or network interface unchanged unless engineering has approved the revised drawing, settings and test scope.
What can cause a poor match?
A KA1-8029 1SFA616920R8029 suffix or order-code difference may identify another coil, contact set, protocol, release, shaft or voltage. A matching appearance is not interchangeability evidence.
If the supplied KA1-8029 1SFA616920R8029 differs from the approved item, quarantine it for review rather than changing field wiring to make it fit.
How is performance proved?
After approved installation of KA1-8029 1SFA616920R8029, inspect retention and operator action. Use only documented safe test methods and include connected equipment behavior.
Record the KA1-8029 1SFA616920R8029 as-left results, asset tag, revision, date and witness. Restore alarms, interlocks and normal control before service handover.
What should purchasing retain?
The ABB KA1-8029 1SFA616920R8029 record should include the complete designation, required accessories, label evidence and the current installation manual revision.
For any proposed substitute to KA1-8029 1SFA616920R8029, obtain written confirmation of every changed technical characteristic and the site's acceptance.
Other codes in this same series
The following KA1 references can accompany an ABB KA1-8029 1SFA616920R8029 enquiry. Suffix changes can affect ratings, fit or approvals, so none is an automatic replacement.
No other unassigned KA1 reference is grouped with KA1-8029 1SFA616920R8029 in this release.
Enquiry and acceptance handoff
Quote ABB KA1-8029 1SFA616920R8029 exactly, include the asset tag and duty, and request confirmation of any missing accessories or alternative build.
Keep the approved KA1-8029 1SFA616920R8029 comparison, installation checks and test results in the maintenance record.
