ABB HK1-11(1SAM201902R1001) selection decision record
Start the ABB HK1-11(1SAM201902R1001) enquiry with a precise equipment identity and a defined plant function. The verified values below establish a technical baseline; they do not replace checking the delivered unit.
Verified parameters and fit limits
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | HK1-11(1SAM201902R1001) |
| Product family | HK1 |
| Component role | manual motor starter auxiliary contact |
| Accessory | HK1-11 |
| ABB order code | 1SAM201902R1001 |
| Contacts | 1 NO + 1 NC catalog configuration |
| System | Compatible ABB manual motor starter |
| Duty | Auxiliary indication, not motor power switching |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
Before signing off HK1-11(1SAM201902R1001), check the current ABB documentation and the actual nameplate. Family-level information must not be used as a guaranteed option for every configuration.
What problem does it solve?
ABB HK1-11(1SAM201902R1001) is selected to report the motor starter state to a control circuit. State the actual circuit, loop or motor tag and the operating problem before deciding on a replacement.
A request for HK1-11(1SAM201902R1001) without site duty, installed revision or failure evidence can lead to a technically different part being offered.
What can cause a poor match?
A HK1-11(1SAM201902R1001) suffix or order-code difference may identify another coil, contact set, protocol, release, shaft or voltage. A matching appearance is not interchangeability evidence.
If the supplied HK1-11(1SAM201902R1001) differs from the approved item, quarantine it for review rather than changing field wiring to make it fit.
Which interfaces must match?
For HK1-11(1SAM201902R1001), confirm starter frame, accessory position and contact loading. Compare the original label, mounting, field terminals and power/control supplies with the ABB product reference.
Keep the HK1-11(1SAM201902R1001) electrical or network interface unchanged unless engineering has approved the revised drawing, settings and test scope.
How is performance proved?
After approved installation of HK1-11(1SAM201902R1001), verify NO/NC transfer with starter actuation. Use only documented safe test methods and include connected equipment behavior.
Record the HK1-11(1SAM201902R1001) as-left results, asset tag, revision, date and witness. Restore alarms, interlocks and normal control before service handover.
What changes at installation?
Installing HK1-11(1SAM201902R1001) may affect adjacent wiring, panel access and auxiliary accessories. Check clearance and isolate the correct energy sources under the site's permit system.
Before disturbing HK1-11(1SAM201902R1001), save photos, configuration, parameter values and an alarm baseline. Keep removed parts identifiable until acceptance is signed.
What should purchasing retain?
The ABB HK1-11(1SAM201902R1001) record should include the complete designation, required accessories, label evidence and the current installation manual revision.
For any proposed substitute to HK1-11(1SAM201902R1001), obtain written confirmation of every changed technical characteristic and the site's acceptance.
Other codes in this same series
The following HK1 references can accompany an ABB HK1-11(1SAM201902R1001) enquiry. Suffix changes can affect ratings, fit or approvals, so none is an automatic replacement.
No other unassigned HK1 reference is grouped with HK1-11(1SAM201902R1001) in this release.
Enquiry and acceptance handoff
Quote ABB HK1-11(1SAM201902R1001) exactly, include the asset tag and duty, and request confirmation of any missing accessories or alternative build.
Keep the approved HK1-11(1SAM201902R1001) comparison, installation checks and test results in the maintenance record.
