Schneider MICROLOGIC 6.0 H - LSIG: what to verify for the MasterPact Micrologic 6.0 H trip unit
MICROLOGIC 6.0 H - LSIG identifies this MasterPact Micrologic 6.0 H trip unit enquiry. A shared category collage is used as a reference image, not as an exact photograph of the supplied MICROLOGIC 6.0 H - LSIG item. Before choosing or replacing MICROLOGIC 6.0 H - LSIG, read the complete physical label and compare it with the system drawings and the relevant manufacturer material.
Technical data confirmed at this stage
| Technical item | Verified value / selection note |
|---|---|
| Complete enquiry wording | MICROLOGIC 6.0 H - LSIG |
| Documented family or role | MasterPact Micrologic 6.0 H trip unit |
| Protection shorthand | LSIG: long-time, short-time, instantaneous and ground fault |
| Breaker fit | Confirm frame and firmware |
| Unverified option details | Confirm complete order record and received unit |
A family name or shared code prefix does not establish identical ratings, fit or interchangeability.
The table records the evidence available for MICROLOGIC 6.0 H - LSIG. An absent value is deliberately left open. For MICROLOGIC 6.0 H - LSIG, the complete configuration may determine the coil, firmware, process interface, mounting arrangement or protection rating; use the installed MICROLOGIC 6.0 H - LSIG label and full datasheet before approving a purchase.
What to send with a purchase enquiry
- Full nameplate photograph and exact designation
- Equipment drawing, location and installed revision
- Required accessories, connectors, cables and condition
- Acceptance test and delivery requirements
Put MICROLOGIC 6.0 H - LSIG on a separate quotation line and ask the seller to restate the full code. If a different version is proposed for MICROLOGIC 6.0 H - LSIG, request a written matrix comparing ratings, electrical connections, mechanical fit and software or firmware requirements. The buyer should not accept the substitution merely because it belongs to the same family.
Equipment interface review
Review the immediate neighbours of MICROLOGIC 6.0 H - LSIG in the installation. For a breaker or contactor, check pole arrangement, control supply and auxiliary contacts. For a controller or I/O accessory, check rack, baseplate, network and terminal assignment. For a motor or sensor, check feedback, power, cable and mounting. Apply only the categories relevant to the actual MICROLOGIC 6.0 H - LSIG item.
Compare MICROLOGIC 6.0 H - LSIG against the archived wiring and service record. Record any changes in version, communications, calibration or safety approval. A replacement order for MICROLOGIC 6.0 H - LSIG should identify who will verify those changes and what evidence is required at receiving and commissioning.
Receiving and acceptance
On receipt, inspect the packaging and the actual MICROLOGIC 6.0 H - LSIG marking before installation. Keep serial and revision information in the equipment file. Use the site's electrical and process isolation procedure, then test the specific switching, protection, control, measurement or motion function appropriate to MICROLOGIC 6.0 H - LSIG. Record the result rather than relying on a visual match alone.
If MICROLOGIC 6.0 H - LSIG is a legacy item, separately check lifecycle status, condition, warranty and availability of support. If MICROLOGIC 6.0 H - LSIG is offered as refurbished stock, require inspection and test records. If a newer item is offered instead, keep its new designation distinct from MICROLOGIC 6.0 H - LSIG in the approval chain.
Related-looking designations
No further unassigned MICROLOGIC 6.0-pattern code is indexed with MICROLOGIC 6.0 H - LSIG; any alternative still needs manufacturer and site verification.
Release check
Release MICROLOGIC 6.0 H - LSIG only after the complete identification, applicable technical requirements, offer and receiving plan agree. Keep MICROLOGIC 6.0 H - LSIG visible in the final procurement record and document every approved deviation.
