Selection file for ABB PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP
Use the complete ABB PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP designation for the purchase and asset record. The short family mark alone cannot establish electrical ratings, process options or interchangeability.
Technical selection record
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP |
| Product family | PGS300 |
| Component role | gauge pressure transmitter |
| Family | PGS300 All-Rounder gauge pressure |
| Base accuracy | 0.055% family reference; confirm conditions |
| Output | Verify fitted HART or other option |
| Configuration | Span, process connection, materials and approvals require complete-code review |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
Values shown for PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP are selection checkpoints. Confirm the fitted unit, nameplate and ABB documentation before releasing an order or a site change.
Installation sequence
Before fitting PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP, isolate the affected system by the plant procedure and preserve the approved settings or wiring schedule. Verify mechanical seating and each identified connection.
After connecting PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP, check power, communications and local indications before enabling the controlled equipment.
Application decision
The intended duty of PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP is to report gauge pressure at the assigned process tapping. Record the controlled asset, panel location and circuit or process tag next to the exact code.
A specification for PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP should state the operating conditions rather than assuming another PGS300 item is a drop-in replacement.
Fit and interface gate
Compare PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP with the existing installation for calibrated span, overpressure, wet materials, seal, hazardous-area approval and signal wiring. Keep photos of the nameplate, terminals and accessory arrangement with the enquiry.
If any connector, protective rating or configuration item differs, hold the PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP substitution for engineering review.
Acceptance evidence
At handover for PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP, record zero and span checks with the loop in its intended operating range. Record who witnessed the test, the measured results and any open action.
The PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP asset record should retain the final configuration, revision and commissioning evidence for later troubleshooting.
Related configuration codes
Other PGS300 designations recorded with PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP are shown below for search and enquiry. Their options and ratings can differ; the list does not claim automatic interchangeability.
No further unassigned PGS300 designation is grouped with PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP on this page.
Purchase handoff
Quote the complete PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP designation, the installation tag and the critical interface checks. Ask for nameplate and revision confirmation before dispatch.
When PGS300.K.S9.A.1.A.A.Y.A.H.D1.BC.UP arrives, compare the received unit to the approved selection record and document the final acceptance result.
