FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 technical selection worksheet
Use the complete FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 designation when requesting this WaterMaster electromagnetic flowmeter. The installation must be checked against the actual equipment marking, because a shared product family does not establish identical ratings, options or approvals.
Key technical data
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 |
| Product family | FEW31 |
| Component role | WaterMaster electromagnetic flowmeter |
| System | WaterMaster FEW31 full-bore integral flowmeter |
| Nominal bore | 040 code: DN40, subject to complete designation confirmation |
| Liner | A code: PTFE in ABB ordering matrix |
| Electrode | S code: stainless steel 316Ti/316L in matrix |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
This table identifies the published family facts for FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0. Treat any unlisted option as a selection question, not as an implied specification for FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0. Consult the current ABB data and the installed nameplate before release.
Match the ordered configuration
The most important purchase question for FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 is: Match bore, liner, electrode, flange rating, conductivity, installation orientation and output configuration. Record any missing suffix, revision, calibration or approval with the supplier.
Ask whether the offered FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 item includes the required terminals, accessories and documentation. Any suggested substitute needs a line-by-line comparison, not an assumption based on the family prefix.
What the device does
The work assigned to FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 is specific: Measure conductive-liquid flow in a filled process line using the specified sensor and transmitter arrangement. Record the controlled process, feeder or network point in which FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 operates.
Check the upstream source and the downstream load or signal as a complete path. For FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0, an apparently matching connector or housing does not establish functional equivalence.
Commissioning evidence
The practical acceptance check for FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 is: Check empty-pipe and zero behavior, then compare indicated and transmitted flow under a known condition. Capture actual readings, states or faults rather than reporting only that the device powered up.
Close the work order for FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 with the observed test result, final configuration and responsible reviewer. If a safety or protective function is involved, follow the site-specific validation procedure.
Installation boundary
Before fitting FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0, isolate the process or electrical system under the site procedure and check the drawing, connection, mounting and environmental limits.
Document the original terminals and settings for FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0. Reapply only approved wiring and parameter changes; retain the previous unit identification for traceability.
Other codes within this series
The following FEW31 designations are grouped on the FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 page to aid searches and enquiries. They may differ in rating, options, protocol or dimensions. Confirm each full designation before substitution.
- FEW31-1.050.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0
- FEW31-1.080.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0
- FEW31-1040H1S1S4B1A1A0A1A1A1M5
Enquiry details to send
Quote FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0 exactly, then state the installed equipment, required quantity, delivery location and whether a new unit or an approved service spare is needed.
For FEW31-1.040.A.1.S.0.S2.B.1.A.1.A.0.A.1.B.0.A.0, request the current datasheet, option confirmation and lead time. On receipt, compare the supplied marking to the approved enquiry and retain the commissioning notes with the equipment record.
