ABB 1SAX111001R1104 (E16DU-6.3): engineering decision notes
The full ABB 1SAX111001R1104 order code identifies the E16DU-6.3 version to review. Use the questions below to distinguish the specified unit from a visually similar part before procurement.
Technical data at a glance
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | 1SAX111001R1104 |
| Product family | E16DU-6.3 |
| Component role | 2–6.3 A electronic motor overload relay |
| Full order code | 1SAX111001R1104 |
| ABB type | E16DU-6.3 |
| Current setting | 2.0–6.3 A in ABB catalog |
| Trip class | Selectable 10E, 20E or 30E |
| Contacts | One NC trip and one NO signal contact |
| Supply | Self-supplied; check approved contactor pairing |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
The ABB 1SAX111001R1104 values shown here come from the cited manufacturer specification where stated. Confirm project-specific options and the delivered label before installation.
Which designation and host must match?
Write ABB 1SAX111001R1104 in full on the order, along with type E16DU-6.3. Compare the installed marking, hardware revision and host equipment rather than relying on the short family name.
For ABB 1SAX111001R1104, check motor full-load current, contactor frame, reset mode and trip class. Similar modules may differ by I/O mix, network role, contact technology, environmental variant or package quantity.
What duty is this code being asked to perform?
ABB 1SAX111001R1104 is intended to protect the selected motor feeder from overload and phase loss. Start with the machine or panel drawing and identify the exact point where this function is required.
A replacement request for ABB 1SAX111001R1104 should include the reason for change: failed hardware, planned upgrade, missing accessory or renewed safety validation. Each reason has a different acceptance threshold.
What must be saved before the change?
Before touching ABB 1SAX111001R1104, apply the site's isolation and stored-energy rules. Save the original configuration, parameter image or wiring evidence where the device is programmable.
Label every ABB 1SAX111001R1104 lead and take photographs of the installed assembly. Protect spare contacts and module pins from damage; preserve the removed part until acceptance is signed.
What interfaces require confirmation?
Trace each ABB 1SAX111001R1104 supply, terminal and communications connection against the as-built schematic. Record cable type, terminal map, connector orientation and any controller configuration.
If ABB 1SAX111001R1104 is a networked or programmable unit, verify project file, firmware, addresses and protocol support. If it is an electrical accessory, confirm its load and mounting coordination.
How is the delivered item checked?
Inspect the ABB 1SAX111001R1104 package, article label and revision at goods receipt. Check the included terminal units, accessories and any license status against the approved purchase specification.
Do not substitute a neighboring ABB 1SAX111001R1104 family code solely because the housing looks alike. Escalate any discrepancy to the site's engineering owner before the maintenance window.
What test demonstrates correct operation?
With ABB 1SAX111001R1104 installed under the approved procedure, injection-test trip time, indication and reset. Record the pre-test state, expected response and measured result.
For ABB 1SAX111001R1104, include negative or fault-path checks when the function is protective, safety-related or communications-critical. Sign off the test only after normal operation and diagnostics agree.
What evidence should stay with the asset?
Store the ABB 1SAX111001R1104 purchase code, delivered label, configuration, firmware and test evidence in the asset record. This prevents later maintenance from relying on an abbreviated description.
A future enquiry for ABB 1SAX111001R1104 should use the validated record and ask the supplier to disclose any change of article, option, packaging or product life-cycle status.
Three-point release record
- Confirm the complete ABB 1SAX111001R1104 article and host fit.
- Record the ABB 1SAX111001R1104 configuration and installation checks.
- Witness the ABB 1SAX111001R1104 functional acceptance test.
Keep the ABB 1SAX111001R1104 manufacturer reference and signed field result with the installed asset.
