ABB 1SAE341111R0640 application and verification guide
Use the following decision gates to specify ABB 1SAE341111R0640 for an existing installation and to accept the delivered unit against the engineering record.
Key technical parameters
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | 1SAE341111R0640 |
| Product family | ESB40-40N-06 |
| Component role | 40 A modular installation contactor with four NO poles |
| Complete order code | 1SAE341111R0640 |
| ABB product series | ESB40-40N-06 |
| AC-1 current | 40 A |
| Main poles | 4 NO |
| Control supply | 230 V AC/DC for the -06 code |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
The values for ABB 1SAE341111R0640 derive from the linked ABB product information. Check the delivered label and application-specific limits before use.
Gate 1 — identity and duty
ABB 1SAE341111R0640 is intended to switch the documented single- or three-phase load. Obtain the full article code from the device or approved drawing before placing the order; the series name alone does not define its rating or options.
Compare ABB 1SAE341111R0640 with the original circuit duty, switching frequency, fault level and environmental conditions. An adjacent number in the series can be a different electrical part even when the housing looks alike.
Gate 2 — electrical interface
Check the ABB 1SAE341111R0640 current, voltage and contact or I/O arrangement against the installed circuit. Trace every supply and feedback conductor, then note required auxiliary devices or overload protection.
For ABB 1SAE341111R0640, verify control voltage, contact count, duty and DIN-rail space. Do not infer a replacement from a photograph or a broad product-family claim.
Gate 3 — mechanical interface
Review ABB 1SAE341111R0640 mounting width, terminal access, cable bend space and enclosure clearance before the shutdown. A different generation may reposition connectors or change accessories.
Keep the ABB 1SAE341111R0640 host equipment and wiring diagram in the work pack. If the original assembly has add-on blocks or busbar links, confirm their compatibility separately.
Gate 4 — settings and coordination
Record every relevant ABB 1SAE341111R0640 current dial, trip class, reset mode, control supply or fieldbus setting. Compare them with the approved protection study rather than copying a nearby machine's settings.
Where ABB 1SAE341111R0640 is magnetic-only, provide the separately designed overload function. Where it is a controller, retain the configuration and network files needed for restoration.
Gate 5 — acceptance test
After qualified personnel install ABB 1SAE341111R0640, confirm commanded pickup and all four pole states. Capture the test method, actual results and any revised settings in the commissioning record.
For ABB 1SAE341111R0640, check the normal state, commanded change and fault or off-state as applicable. Return the circuit to service only after the assembled function is accepted.
Gate 6 — spare governance
Archive the ABB 1SAE341111R0640 label photo, manufacturer document and as-left record with the asset. If the unit later becomes unavailable, request a written successor comparison rather than silently changing the order code.
The ABB 1SAE341111R0640 page is a purchasing reference for the exact marked article. Same-series alternatives are grouped below only as enquiry references; their settings and interfaces still need individual checking.
Other order codes in this series
These designations are listed under ABB 1SAE341111R0640 as related same-series variants. They may differ in current, supply, contacts or equipment generation, and are not presumed interchangeable. A code included here is not assigned a separate product page.
- 1SAE341111R0740
Release and handover
Before buying ABB 1SAE341111R0640, confirm exact marking, interfaces and approved settings with the site engineer.
After fitting ABB 1SAE341111R0640, save the test evidence and update the equipment spare record.
